Build to Rent (BTR): What It Is and How It's Zoned

Build to rent means homes built to lease. See how U.S. zoning and subdivision rules can apply and how to screen a site using public records.

Pillar team12 min read

Build to rent (BTR) means homes built to be rented rather than sold: usually single-family houses or townhomes in one community, held by one owner that leases and manages them. "Build for rent" (BFR) means the same thing. For the land, the key question is whether the homes sit on individually platted lots or on one undivided parcel.

This guide, written by Pillar, a land research company, covers the development side: zoning, site screening and the public record. We read every source linked here on November 20, 2026. It is general information, not legal advice; confirm the rules for your site with a land use attorney or planner licensed in your state.

What is build to rent?

Build to rent describes how homes are planned and held, not a building type. The National Association of Home Builders (NAHB), which tracks the segment, counts "homes built and held by the builder for rental purposes" (NAHB, August 21, 2026). HUD describes BTR communities as "multifamily rental properties that consist of detached single-family homes, duplexes, or triplexes" (Mortgagee Letter 2026-12).

BTR vs. single-family rental (SFR). Any rented house is a single-family rental, including one an investor bought from a previous owner. A BTR home is rental housing from the start: the January 2026 executive order quoted in HUD's letter calls for exceptions for "Build-to-Rent properties that are planned, permitted, financed and constructed as rental communities."

BTR vs. apartments. BTR spreads units out as houses, duplexes or townhomes. For its FHA programs, HUD separates the property from the building: "While BTR is a 'multifamily' property, the individual detached single-family house onsite is not a 'multifamily' building" (Mortgagee Letter 2026-12, § III.6).

How many build-to-rent homes are being built?

NAHB's analysis of Census Bureau data puts single-family built-for-rent starts at about 15,000 in the second quarter of 2026 and 18,000 in the second quarter of 2025, though NAHB cautions that quarter-to-quarter movements in this small segment typically are not statistically significant. In the four quarters through Q2 2026, 63,000 homes started, down 16% from 75,000 in the prior four quarters. The four-quarter moving average share of single-family starts was just under 7%, against a 1992 to 2012 average of 2.7% (NAHB). The count excludes homes sold to another party to rent; based on industry surveys, NAHB estimates those may represent another 3% to 5% of single-family starts.

Platted lots or horizontal apartments: the two forms of BTR

Sketch how the land will be divided before you read the zoning code.

Homes on individually platted lots. Each home sits on its own lot on a recorded subdivision plat, like a for-sale neighborhood. A UNC School of Government analysis of North Carolina law says "If a build-to-rent development is a townhome development, the standard zoning rules for townhome development will apply."

Homes on one undivided parcel ("horizontal apartments"). The homes share one lot and are run like an apartment complex. Depending on the code, this may fall under a multifamily or cottage-court use; Henry County's definitions of both, below, contemplate a single lot.

The form can change where lot standards are measured, whether subdivision review applies and which financing fits.

Build to rent zoning: how named codes treat it

Of the codes we read, only Snellville's uses the words "build to rent."

Snellville, Georgia: separate BTR districts. The city's Unified Development Ordinance, as amended through June 22, 2026, lists six "Build-to-Rent" residential districts (Sec. 101-2.1). RS-30-BTR (Sec. 202-11) is meant for "high-quality single-family houses that can be rented to residents" on lots of at least 30,000 square feet and 100 feet wide. Its additional requirements (Sec. 202-11.9) call for a property owners association with mandatory membership for all parcels; the association or its management company maintains all grounds and building exteriors. Driveways must be at least 24 feet wide and 30 feet long (Sec. 202-11.9.A.5). R-TH-BTR (Sec. 202-15) is "intended exclusively for rentable single-family attached dwelling units and customary accessory uses and structures," at up to 8 units per acre. The city's online code and this PDF differ in places, so confirm the current text with the city.

Henry County, Georgia: a multifamily definition that counts buildings on one lot. The county's Unified Land Development Code (full revision dated September 1, 2026) defines multifamily as "Three or more dwelling units in one building, or in multiple buildings on a single lot, with the number of families not exceeding the number of dwelling units provided" (Sec. 6.3.1.I). Table 6.1 marks multifamily permitted in R-M and M-U. The R-5 intent statement mentions "horizontal multifamily and townhome developments, where appropriate" (Sec. 3.6.1), but Table 6.1 has no multifamily entry for R-5. The definition does not settle how a particular detached layout is classed; ask county staff which use row applies. Table 6.1 also marks cottage courts permitted in R-X, R-M and M-U, subject to Sec. 6.3.1.K: 4 to 12 detached dwellings per central common area (a development may have more than one cluster), each up to 1,200 square feet of heated and conditioned space. A cottage court "may be developed on individual fee simple lots or a single lot with a common form of ownership, such as a condominium." The section also sets frontage and access, porch, common-area, parking and driveway standards.

Fort Worth and Texas: the plat can decide the class. In Fort Worth's Urban Residential district, the zoning ordinance says "A townhouse form is regarded as an apartment/ condominium when on one platted lot and not individually platted lots with ground floor separate entrances to each unit" (§ 4.713(c)(1)b). Statewide, Texas Local Government Code Chapter 218, added by Senate Bill 840, defines "multifamily residential" as "the use or development, as applicable, of a site for three or more dwelling units within one or more buildings" (§ 218.001). For projects initiated on or after September 1, 2025 (SB 840, § 4), § 218.101 applies to cities over 150,000 wholly or partly in counties over 300,000 (§ 218.002). They must allow multifamily residential use and development where zoning allows office, commercial, retail, warehouse or mixed-use projects or uses, without requiring changes or discretionary exceptions to zoning or land-use rules. Section 218.101(c) excludes classifications that allow heavy industrial use, land within 1,000 feet of an existing heavy industrial use or development site or 3,000 feet of an airport or military base, and city-designated clear or accident potential zones. Check the applicable development standards and administrative approvals under §§ 218.003 and 218.102. Ask the city in writing whether it treats detached rental homes on one site as multifamily residential.

North Carolina: zoning and subdivision rules, not ownership. The UNC School of Government analysis (May 24, 2022) concludes that "under current law a local government could not use zoning or land subdivision regulations to regulate build-to-rent development differently from comparable owner-occupied development." Generally applicable zoning and subdivision rules still apply, and it notes that "the division of a tract into sites for single-family residential rentals also may qualify as a subdivision" under G.S. 160D-802.

How to screen a site for build-to-rent zoning

  1. Find the current district. Read it from the official zoning map and the parcel record, then open that district's section of the code and note its amendment date.
  2. Sketch the form. Lay out lots or buildings, then ask staff which use rows (single-family, townhouse, cottage or multifamily) and subdivision rules apply. Our R3 zoning guide shows how codes write multifamily districts.
  3. Read the use table: permitted, conditional or not listed. A conditional or special use needs a separate approval; see conditional use permits. If the use is not listed, ask staff whether the path is a rezoning or a planned unit development, and check the future land use map.
  4. Confirm the subdivision path. Ask what plat approval your proposed building sites and leased areas need under the local subdivision ordinance.
  5. Check water and sewer. Ask each provider about capacity and a will-serve letter. Snellville's R-TH-BTR purpose statement says R-TH districts "are located where public water supply and sewerage facilities are available and where there is direct access to collector streets, major streets or State routes."
  6. Look for rental restrictions. Read the recorded covenants and any HOA declaration for leasing limits; as the North Carolina analysis notes, "Private agreements such as deed restrictions and covenants may limit the extent to which property may be rented." See deed restrictions before buying land.
  7. Get staff's answer in writing. Keep the email or zoning verification letter with the code section it relies on.

What else to check on a build-to-rent site

  • Density and open space. How many homes per acre does the district allow, and how much of the site must stay open?
  • Access. Does the parcel have legal access, and will the number of homes trigger a second entrance? See road frontage vs. legal access.
  • Flood and wetlands. FEMA calls its Flood Map Service Center "the official public source for flood hazard information produced in support of the National Flood Insurance Program (NFIP)." Use the Fish and Wildlife Service's Wetlands Mapper for an initial screen. It maps wetland type and extent. Ask the relevant agencies about jurisdiction and rules before making changes in or near wetlands (NWI FAQ).
  • Impact and tap fees. Will the city and the utility charge per home or per multifamily unit for the form you chose?

How are build-to-rent communities financed?

Industry interviews summarized by the Urban Institute (June 2023) found that builders who hold their own homes, and investors who hire a builder, rely on acquisition, development and construction loans, generally from banks. Partnerships may need bridge funding when investors take possession of many homes at once with certificates of occupancy. Investors generally move to permanent financing once most homes are rented. FHA mortgage insurance is another route for projects that meet HUD's criteria.

Since October 14, 2026, HUD accepts applications for FHA multifamily mortgage insurance on BTR communities (announcement, Mortgagee Letter 2026-12): under Section 221(d)(4) for new construction only, and under Section 223(f) for acquisition or refinancing of communities whose certificate of occupancy is dated less than 3 years before application. The land-stage conditions are in § III.1: five or more long-term rental units on a single cohesive, contiguous, characteristically uniform site operated as one multifamily rental property. HUD prefers one tax parcel and accepts contiguous parcels that form a single site defining the insured collateral. No interspersed privately owned parcels or residences are allowed, and HUD will not approve sales of parcels or buildings, or partial release of collateral, during the insured loan term. Lenders must address underwriting and accessibility in applications for sites mixing BTR and traditional multifamily buildings. Manufactured or modular construction issues require review at the concept meeting.

Section 1001 of the 21st Century ROAD to Housing Act (Public Law 119-101, July 11, 2026) bars a "large institutional investor" from purchasing, or contracting to directly or indirectly purchase, a single-family home (up to 2 dwelling units, each intended for one household; manufactured homes excluded). "Purchase" includes other acquisitions, including construction. The law covers for-profit entities whose business includes investing in, owning, renting, managing or holding single-family homes and that, alone or with others, have direct or indirect investment control of at least 350 such homes after enactment. Excepted purchases after enactment are excluded from the count (§ 1001(a)(3)). Exceptions (§ 1001(a)(2), (b)(2)) include purchases under build-to-rent programs of newly constructed homes to be managed as rentals, in all-renter or mixed owner- and renter-occupied single-family communities, and certain reorganizations of homes owned or purchased on or before enactment. The ban takes effect 180 days after enactment (January 7, 2027, by our count) and is repealed 15 years later; Treasury may issue regulations (§ 1001(b)(4)). If your buyer or capital partner could be covered, have counsel read the section.

Living in or buying near a build-to-rent community

Renting. You sign a lease with the community's owner or its manager. Under these FHA programs, HUD requires BTR properties to be "professionally managed similar to comparable multifamily projects in the market, including other BTR projects," and management and maintenance not on site must have an adequately staffed local presence in the market area (§ III.2).

Buying one of the homes. If an individual sale is proposed, check what the seller can convey under the recorded ownership documents and which local approvals and loan terms apply, including the FHA sale limit above.

Buying next door. Look up the BTR tract's zoning and recorded plat with the county; they show how the land is zoned and divided.

Finding land for a build-to-rent community

Three places to look:

  • Edge-of-growth tracts with utilities nearby, where zoning or the future land use map points to residential; see finding off-market development land.
  • Finished lots offered in bulk. Read the recorded plat's notes and the covenants for leasing limits.
  • Land already zoned for attached or multifamily housing, which can suit the one-parcel form.

In the deal documents, compare the approved site plan with the recorded plat. Review the title commitment and its underlying documents for covenants, HOA declarations, recorded access and easements, and use the survey to locate them on the ground. Tie zoning, plat and utility approvals to the contract's feasibility period; see the land acquisition process and land feasibility study guides.

Before an offer, answer each of these: district and use path, lots or one parcel, utilities, flood and wetlands, leasing limits in title, access, and what your lender or buyer requires. For that first pass, Pillar shows available parcel zoning facts and acreage on the same map as the FEMA flood hazard layer (Pillar for homebuilders); check the official code, the recorded plat and staff's written response for your site.

Quick answers

What does BTR mean in real estate? Build to rent: homes built to be rented and held by one owner, usually in a single community.

Is build for rent (BFR) the same as build to rent? Yes. BFR and BTR name the same product.

What are horizontal apartments? A BTR community of detached or small attached homes on one undivided parcel, run like an apartment complex. Henry County, Georgia's multifamily definition includes three or more units "in multiple buildings on a single lot," with no more families than units; ask staff which use applies to your layout.

Does build to rent need special zoning? It depends on the code. Snellville, Georgia has separate BTR districts. In North Carolina, a May 2022 UNC School of Government analysis of then-current law concludes local zoning and subdivision rules cannot treat BTR differently from comparable owner-occupied development; generally applicable rules still apply.

Can you buy a build-to-rent home? If the owner offers one, check what the seller can convey under the recorded ownership documents and which approvals and loan terms apply. Under these FHA programs, HUD will decline to approve parcel or building sales during the insured loan term.