R3 Zoning: What It Means and What You Can Build
R3 zoning means different things locally. Compare five real R3 codes, R2 vs R3 vs R4, and learn how to check what a lot allows.
R3 zoning (also written R-3) is a residential zoning district that each city or county defines for itself. There is no national zoning code. Los Angeles and Anchorage, Alaska, use R3 for multifamily housing. Malvern, Pennsylvania, uses it for single- and two-family dwellings, and Henderson County, North Carolina, uses it for low-density residential land.
This guide is written by Pillar, a land research platform. The figures come from each jurisdiction's code or planning department and from one state agency handbook, read on November 16, 2026. Codes change, so open the linked section before relying on a number. This is general information, not legal advice; confirm the rules for your lot with a licensed professional in your state.
What does R3 zoning mean?
The "R" means residential. The "3" means whatever the local code says. In the five codes we read, it means four different things:
- A multifamily zone. Los Angeles calls R3 the "Multiple Dwelling Zone" (LAMC section 12.10). Anchorage, Alaska, describes its R-3 as "a multifamily residential district" (Title 21, section 21.04.020).
- A one- and two-family zone. The Borough of Malvern, Pennsylvania, says its R3 districts "are intended to provide medium-density single- and two-family dwelling units" (zoning chapter, Article VI).
- A density. Fairfax County, Virginia, names R-3 the "Residential District, Three Dwelling Units/Acre".
- A low-density district. In Henderson County, North Carolina, the purpose of Residential District Three is "to foster orderly growth where the principal use of land is low density residential" (section 42-30). Its numbers run the other way: R1 has a standard density of 4 units per acre, and R3 allows 0.66.
What can you build on R3 zoning?
The five codes side by side, for the conventional case. Exceptions are in the linked sections.
- Los Angeles, California (R3, Multiple Dwelling Zone). Section 12.10 allows any use permitted in the R2 zone. Its added uses include group dwellings, multiple dwellings, apartment houses, boarding houses, rooming houses, child care facilities for not more than 20 children, senior independent housing and assisted living care housing. The minimum lot is 50 feet wide and 5,000 square feet. A smaller lot that was held under separate ownership or was of record as of September 23, 1956, and was created in conformance with the Subdivision Map Act, may be occupied by any use the section permits, except uses explicitly requiring more than 5,000 square feet of lot area. The minimum lot area per dwelling unit is 800 square feet. The front yard is at least 15 feet, or 10 feet on key lots. Side yards are 5 feet for a main building of up to two stories, plus one foot for each story above the second, up to 16 feet. On a lot less than 50 feet wide, the side yard may be reduced to 10% of the lot's width, but not below 3 feet. The rear yard is 15 feet. Section 12.21.1 limits buildings to 45 feet in the portions of R3 that are in Height District No. 1, and to six stories and 75 feet in Height Districts 2, 3 and 4, where a building designed and used entirely for residential purposes is limited only in feet. Limited sub-districts of Height District 1 can be lower: 30 feet in 1-XL.
- Anchorage, Alaska (R-3, Mixed Residential). Section 21.04.020 describes R-3 as "a multifamily residential district with gross densities between 15 and 40 dwelling units per acre," in which housing allowed in the R-1, R-1A, R-2A and R-2D districts is also a permitted use. Table 21.06-1 gives a multifamily dwelling a 6,000-square-foot minimum lot, 50 feet of width, 60% maximum lot coverage, a 10-foot rear setback, a side setback of 5 feet plus one foot for each 5 feet of height over 35 feet, and a 45-foot height limit. A townhouse lot needs 2,000 square feet and 20 feet of width, or 30 feet on a corner lot. A detached house needs 6,000 square feet and 50 feet.
- Malvern, Pennsylvania (R3a and R3b). The uses Article VI permits by right include a single-family detached dwelling, a two-family semidetached dwelling and a two-family duplex. In R3a, a detached house needs 12,000 square feet and 60 feet of width at the building line. A two-family semidetached dwelling needs 10,000 square feet and 35 feet per dwelling unit, and a duplex needs 10,000 square feet per dwelling unit and 60 feet. In both R3a and R3b, the front yard is at least 15 feet and the rear yard is 25 feet for residential uses. Height is three stories or 35 feet, whichever is less, with one exception: where one side yard is reduced by right to five feet, the portion of a structure less than 12.5 feet from that side yard line is limited to 18 feet, which conditional use approval can raise to 35 feet. Sections 220-602 A(3)(c) and B(3)(c) also set a location condition. Building coverage for residential uses is 20% by right and may be increased to 25% with conditional use approval. Lot coverage is 35% for residential uses.
- Fairfax County, Virginia (R-3, three dwelling units per acre). Table 2102.7 caps density at 3 dwelling units per acre. A conventional subdivision lot needs at least 10,500 square feet, with an 11,500-square-foot average, and a width of 80 feet on interior lots and 105 feet on corner lots, which a note says may be modified under subsection 5100.2.K. For single-family dwellings on conventional lots, setbacks are 30 feet front, 12 side and 25 rear, and the height limit is 35 feet. Cluster subdivisions and affordable dwelling unit developments have their own standards.
- Henderson County, North Carolina (R3, low density). Section 42-30 sets residential density at 0.66 units per acre, or 1 unit per 1.5 acres, calculated on the entire acreage of the tract. Side and rear setbacks are 15 feet. The front setback depends on the road: 15 feet on a local road, rising to 90 feet on a freeway. Maximum height is 40 feet. On portions of a tract with a slope of 60 percent or greater, where those areas are ten percent or more of the tract, maximum density is half the eligible density.
Can you build a single-family home in R3?
Yes in four of the five. Los Angeles carries R2's uses into R3, and R2 carries R1's. Anchorage's table has an R-3 row for a detached house. Malvern permits one by right. Fairfax County's table sets setbacks for single-family dwellings. For Henderson County, check the county's use table.
One caution in Los Angeles: under section 12.10 C.5, added effective February 11, 2025, there is a required minimum density of one dwelling unit or guest room, counting accessory dwelling units, for every 2,000 square feet of lot area. It applies to every Housing Development Project on a lot that meets the zone's minimum width and area, prior to any subdivision, except when section 12.22 C.28 applies. The figure is rounded up to the nearest unit, and the rule does not apply if the zone's lot area per unit does not allow that density to be built. Ask the planning counter whether it covers your project.
Can you build a duplex or apartments in R3?
- Los Angeles: yes to both. A two-family dwelling comes in through the R2 uses, and section 12.10 lists apartment houses and multiple dwellings.
- Anchorage: yes to both. Table 21.06-1 has R-3 rows for two-family, townhouse and multifamily dwellings.
- Malvern: a duplex, yes, by right. As we read Article VI, apartment buildings are not on its by-right or special exception lists.
- Fairfax County: the table's residential standards are for single-family dwellings. Read the use regulations in Article 4 for anything else.
- Henderson County: section 42-30 mentions two-family attached dwellings and multifamily dwellings, and says developments proposing ten or more multifamily dwellings must apply as a conditional rezoning. The county's use table decides what is permitted.
California ADU law can add units on a multifamily lot. The Department of Housing and Community Development's March 2026 ADU Handbook says up to two detached ADUs are allowed on a lot with a proposed multifamily dwelling, and up to eight on a lot with an existing one, not to exceed the number of existing units, subject to four-foot rear and side setbacks and height limits (Government Code section 66323).
How many units can you build on an R3 lot?
Do the arithmetic from the code, not the label. These are base allowances; yards, height, parking, open space and approvals still decide what fits.
- Los Angeles, lot area per unit. Take a 7,500-square-foot lot, 50 feet wide. At 800 square feet per dwelling unit, 7,500 divided by 800 is 9.375, so as we read it the base allowance is 9 units. A tenth would need 8,000 square feet. The Department of City Planning's zoning summary, updated January 2026, converts the same ratio to 54.45 dwelling units per acre.
- Fairfax County, units per acre. At 3 dwelling units per acre, 2 acres times 3 is at most 6 dwelling units in a conventional subdivision, each on a lot of at least 10,500 square feet. The ordinance's density definition controls how acreage is counted. See how big an acre is for the conversions.
- Henderson County, acres per unit. The code's own example is a 5-acre tract at 0.66 units per acre, which it says yields 3 permitted dwelling units.
Small lots have a cap in Los Angeles: section 12.10 C.4 permits no more than two dwelling units on a lot of less than 4,000 square feet. That is the zoning section's rule, not the whole answer. The section points to section 12.22 C for exceptions to its area regulations, and HCD's handbook says ADUs that conform to Government Code section 66314 are not considered to exceed the allowable density for the lot.
What is the difference between R2 and R3 zoning?
In three of the four codes below, R3 is denser than R2. Our R1 guide covers the first rung. The size of the step differs:
- Los Angeles: the lot minimum stays at 5,000 square feet. The lot area per dwelling unit drops from 2,500 square feet in R2 to 800 in R3, and apartment houses become a listed R3 use. R2 allows them only on a lot whose side lot line adjoins a lot in a commercial or industrial zone, with further conditions.
- Anchorage: R-2M has gross densities between five and 30 dwelling units per acre, and its residential buildings may contain no more than eight dwelling units. R-3 runs from 15 to 40 units per acre, and multifamily lot coverage rises from 40% to 60%.
- Fairfax County: density rises from 2 to 3 dwelling units per acre, and the conventional minimum lot drops from 15,000 square feet in R-2 to 10,500.
- Henderson County: the step goes down. R2 has a standard density of 1 unit per acre. R3 allows 0.66.
What is the difference between R3 and R4 zoning?
- Los Angeles: R4 halves the lot area per dwelling unit again, from 800 to 400 square feet. It also adds uses, including child care facilities or nursery schools, fraternity or sorority houses and dormitories, and retirement hotels.
- Anchorage: R-4 is "a multifamily medium to high density residential district." Its maximum floor area ratio is 1.5, which may be increased through the code's bonus provisions.
- Fairfax County: R-4 allows 4 dwelling units per acre, with an 8,400-square-foot conventional minimum lot and an 8,800-square-foot average.
- Henderson County: R4 allows 0.20 units per acre, or 1 unit per 5 acres.
Which R3 uses need special approval?
R3 zoning restrictions are not only about lot size. Some uses need a discretionary approval, whose name differs by place.
- Los Angeles. On a lot the community plan's land use map designates as Public, Quasi-Public, Public/Quasi-Public Use, Other Public or Open Space, any R3 use needs prior approval under section 12.24.1. Section 12.10 B applies the same rule to several other kinds of lot.
- Malvern. A bed-and-breakfast, a funeral home, a major home occupation and a supplemental dwelling unit each need a special exception from the Zoning Hearing Board.
- Henderson County. Any use that requires a special use permit has a maximum impervious surface of 80% and a maximum floor area of 80,000 square feet, with some operations excluded from the floor area limit.
See conditional use permits for the process, and zoning variances for relief from a setback or height standard.
How do you look up a parcel's zoning and read the R3 rules?
Los Angeles. The Department of City Planning's ZIMAS brochure gives the steps:
- Go to zimas.lacity.org and search by address, street intersection, assessor parcel number or legal description.
- Expand the Planning and Zoning tab to see the underlying zone.
- Check whether the site is in a Specific Plan Area or Overlay Zone, which can carry additional restrictions.
- Open section 12.10 for R3, then section 12.21.1 for the full height district, including any suffix. The R3 limit is 45 feet in Height District No. 1, 30 feet in 1-XL, and 75 feet in Height Districts 2, 3 and 4.
Fairfax County. The county's page How Do I Find My Zoning District? links to the Zoning District Analyzer, an interactive map of existing zoning districts that can be searched by address. The same page links to a property search by address or tax map reference, which shows the zoning district from the assessment records. Then open the district's section in the Zoning Ordinance.
Anywhere, write down the full label, including suffixes, and confirm it with the planning office.
What should a land buyer or developer check on an R3 lot?
Unit yield. Run the density arithmetic above first, then test it against yards, height and coverage.
Parking. Los Angeles's zoning summary, which calls itself only a guide, says R3 parking is the same as in the RD zones, where it lists one space per unit with fewer than three habitable rooms, 1.5 spaces per unit with three habitable rooms, and two spaces per unit with more than three. Treat those as the summary's ratios, not a project's final requirement. Los Angeles City Planning says California's AB 2097 prohibits cities from imposing a minimum automobile parking requirement on most development projects within a half-mile radius of a major transit stop, with limited exceptions. ZIMAS has an "AB 2097 Eligibility" field under Planning and Zoning.
Open space. The same summary says open space is required for six or more residential units, under section 12.21 G. In Fairfax County's R-3, a cluster subdivision must keep 25 percent of its gross area as open space; a conventional one has no requirement.
Overlays. Anchorage's chapter 21.04 says overlay district regulations apply in addition to the base district's, and that the overlay controls in an express conflict. For caps on hard surfaces, see impervious surface limits.
Rezoning. If R3 doesn't allow the project, the usual routes are a rezoning or a planned district. Start with the adopted plan; our guide to zoning vs. future land use explains how the two maps relate. A planned unit development is the site-specific alternative. If the lot adjoins a business district, read what commercial zoning allows too.
Deal documents. The zoning label comes from the jurisdiction's zoning map and code, not from the listing. Read the deed, the title commitment's exceptions, the recorded plat and any covenants, because private restrictions are separate from zoning and can be stricter.
Pillar's map layers show zoning alongside floodplain, wetlands, utilities and future land use over parcel boundaries. Coverage varies by dataset, and a map label is not the code, so confirm anything decisive with the jurisdiction.
Quick answers
What does R3 zoning mean? A residential district whose rules are set locally. It is a multifamily zone in Los Angeles and Anchorage, a one- and two-family zone in Malvern, a three-units-per-acre district in Fairfax County and a low-density district in Henderson County.
Can you build apartments or a single-family home on R3? Los Angeles and Anchorage allow both. Malvern's R3 lists houses and two-family dwellings by right, not apartment buildings. Elsewhere, read the district's use list.
How many units can you build on R3? Los Angeles requires 800 square feet of lot area per dwelling unit. Fairfax County allows 3 dwelling units per acre. Henderson County allows 1 unit per 1.5 acres.
What is R3 zoning in California? Each city and county defines its own. Los Angeles's R3 is a multiple dwelling zone with 800 square feet of lot area per unit. State ADU law applies on top.
What is the difference between R2 and R3? In Los Angeles, the lot area per unit drops from 2,500 to 800 square feet. In Fairfax County, density rises from 2 to 3 units per acre. In Henderson County, R3 is less dense than R2.
What is the minimum lot size in R3? There is no standard. Los Angeles's base minimum is 5,000 square feet, with an exception for qualifying lots held separately or of record as of September 23, 1956. Malvern's R3a requires 12,000 for a detached house. Henderson County regulates by acres per unit instead.