Base Flood Elevation (BFE): What It Is, How to Find It

Base flood elevation is the height floodwater should reach in a 1 percent chance flood. Find yours by address, read the datum and see how high to build.

Pillar team14 min read

The base flood elevation (BFE) is the height floodwater is expected to reach during the base flood, the flood with a 1 percent chance of being equaled or exceeded in any year. It is an elevation measured from a vertical datum, not a depth of water. FEMA prints it on flood maps, and building rules are measured against it.

Pillar, a land research software company, wrote this guide from federal regulations, FEMA pages and the state codes named, each read on November 16, 2026. It is general information, not legal, engineering or insurance advice. Confirm the elevation and rules for your property with the local floodplain administrator and a licensed surveyor or engineer in your state.

What is base flood elevation?

  • The base flood. 44 CFR 59.1 says it "means the flood having a one percent chance of being equalled or exceeded in any given year." People call it the 100-year flood.
  • The base flood elevation. FEMA's glossary defines it as "The elevation of surface water resulting from a flood that has a 1% chance of equaling or exceeding that level in any given year." The same entry says it is shown on the Flood Insurance Rate Map (FIRM) for a list of zones that includes AE, AH and VE.

A BFE of 12 does not mean 12 feet of water on your lot. It means the flood surface is expected to reach elevation 12 on the map's datum. The depth at any spot is that number minus the ground elevation there.

Is base flood elevation above sea level?

Loosely, yes. Precisely, it is a height above a vertical datum. 44 CFR 59.1 defines "mean sea level" as "the National Geodetic Vertical Datum (NGVD) of 1929 or other datum, to which base flood elevations shown on a community's Flood Insurance Rate Map are referenced."

The lookups below returned two datums, NGVD 29 and NAVD 88. They are different reference systems, so the same point has a different number on each. A BFE means nothing without its datum, and a survey on the other datum must be converted before you compare the two. Our NGVD 29 vs NAVD 88 guide covers the conversion.

How to find the base flood elevation for an address

These steps describe FEMA's pages as they were on November 16, 2026.

  1. Search the address at the Flood Map Service Center. The search box at FEMA's Map Service Center takes "an address, a place, or longitude/latitude coordinates."
  2. Write down the map number and effective date. The results page has a line for both, a "Dynamic Map" and a "Map Image" view, a list of "Changes to this FIRM" and a "Go To NFHL Viewer" link.
  3. Open the NFHL Viewer. FEMA says that in the NFHL Viewer "you can use the address search or map navigation to locate an area of interest," and that its print tool makes a full FIRM or a FIRMette, a printable section of one.
  4. Read the zone, then the elevation. A BFE appears in one of two ways:
    • One elevation for the whole zone. FEMA's study guide for local floodplain officials says "For AE Zones, or coastal and lake floodplains, use the BFE printed in parentheses below the flood zone designation. No interpolation is necessary." FEMA's Flood Hazard Zones data has a STATIC_BFE field, which held the 8 and the 9 in the lookups below.
    • Lines across a river floodplain. Along rivers, the guide reads the BFE from the "wavy lines" on the FIRM and from lettered cross-sections.
  5. Note the datum. The data layers carry it in a V_DATUM field, and FEMA's study training says the Flood Insurance Study has a section naming the vertical datum.
  6. Use the Flood Insurance Study for a point between lines. The same guide says the elevations on the FIRM "are rounded to the nearest foot" and that "the flood profiles should always be used to determine flood elevations along rivers and streams." A flood profile is a graph in the study report, with distance along the stream on one axis and elevation on the other. Find your site along the stream and read the base flood line. For coastal floodplains and AO and AH zones, the guide says the FIRM "is the only source of base flood elevations." The Map Service Center's FAQ says to find the study report with "the Search All Products feature."
  7. Check for changes. Look at the changes listed on the results page, and at preliminary or pending maps in the Flood Map Changes Viewer linked from FEMA's NFHL page.

Three real lookups. On November 16, 2026, we located three addresses with the Census Bureau geocoder and queried FEMA's NFHL map service at each point:

  • 1700 Convention Center Dr, Miami Beach, Florida. Zone AE, static BFE 8 feet, datum NGVD 29. Panel 12086C0317L, effective September 11, 2009.
  • 450 Bay Front Pl, Naples, Florida. Zone AE, static BFE 9 feet, datum NAVD 88. Panel 12021C0393J, effective February 8, 2024.
  • 500 1st Ave NW, Cedar Rapids, Iowa. Zone AE, no static BFE. Cedar River cross-sections within 1,500 feet: AL at 723.7 feet, AM at 724.7 and AN at 725.3, all NAVD 88. Panel 19113C0410E, effective July 20, 2021.

The Florida numbers sit on different datums, so they cannot be compared as printed. As we read FEMA's guide, the Cedar Rapids BFE would be read from the Cedar River flood profile. These are point lookups at a geocoded address, not determinations for a parcel or building.

What if there is no base flood elevation? Zones A, AO and V

Zone A. The zone table at 44 CFR 64.3 describes Zone A as an "Area of special flood hazard without water surface elevations determined."

44 CFR 60.3(b) covers communities where FEMA has designated A zones but "has neither produced water surface elevation data nor identified a floodway or coastal high hazard area." Paragraph (c)(1) applies the same standards in communities with more detailed maps. Two parts matter:

  • Large proposals must supply the data. The community must "Require that all new subdivision proposals and other proposed developments (including proposals for manufactured home parks and subdivisions) greater than 50 lots or 5 acres, whichever is the lesser, include within such proposals base flood elevation data."
  • The community must use what exists. It must "Obtain, review and reasonably utilize any base flood elevation and floodway data available from a Federal, State, or other source" as criteria for requiring that development in Zone A meet listed standards, including the lowest-floor rules in (c)(2) and (c)(3).

FEMA's guide for these areas is FEMA 265, Managing Floodplain Development in Approximate Zone A Areas, dated 1995. It says "a detailed method is required under Subparagraph 60.3(b)(3) of the NFIP regulations for proposed development greater than 50 lots or 5 acres, whichever is the lesser." Below those thresholds, where no BFE data are available, it says simplified methods "may be used," and that "communities have the discretion to determine which method should be used." It describes two, contour interpolation and data extrapolation, and says "very specific conditions must be met." The guide also limits them: "Simplified methods are appropriate for floodplain management purposes only," and they "may not be used by the community to complete an Elevation Certificate used for flood insurance rating."

Zone AO. FEMA's glossary says "Average flood depths derived from detailed analyses are shown within these zones." Section 60.3(c)(7) requires new and substantially improved homes in AO zones to have the lowest floor, including basement, "elevated above the highest adjacent grade at least as high as the depth number specified in feet on the community's FIRM (at least two feet if no depth number is specified)."

Zones VE and V. FEMA's glossary says base flood elevations are "shown at selected intervals" in the coastal VE zones, so VE does have a BFE. What is measured against the BFE changes. In Zones V1-30 and VE, and in Zone V if base flood elevation data is available, 60.3(e)(4) measures "the bottom of the lowest horizontal structural member of the lowest floor (excluding the pilings or columns)." Plain Zone V shows no BFE.

How far above base flood elevation should I build?

The federal minimum is the BFE itself. In communities with published elevations, 44 CFR 60.3(c)(2) requires "that all new construction and substantial improvements of residential structures within Zones A1-30, AE and AH zones on the community's FIRM have the lowest floor (including basement) elevated to or above the base flood level," unless FEMA has granted the community an exception allowing basements. For new construction and substantial improvements of non-residential structures in those zones, paragraph (c)(3) gives a second option. The structure, "together with attendant utility and sanitary facilities," must be designed so that below the base flood level it "is watertight with walls substantially impermeable to the passage of water and with structural components having the capability of resisting hydrostatic and hydrodynamic loads and effects of buoyancy." Paragraph (c)(4) then requires a registered professional engineer or architect to develop or review the design and certify it, and a record of those certificates to be kept with the community's designated official.

Freeboard is extra height above the BFE. 44 CFR 59.1 defines it as "a factor of safety usually expressed in feet above a flood level for purposes of flood plain management." FEMA's glossary says freeboard "is not required by NFIP standards, but communities are encouraged to adopt at least a one-foot freeboard."

Two states that write freeboard into the residential code:

  • Florida. Section R322.2.1 of the 2023 Florida Building Code, Residential, Eighth Edition says buildings in flood hazard areas, "not including flood hazard areas designated as Coastal A Zones, shall have the lowest floors elevated to or above the base flood elevation plus 1 foot (305 mm), or the design flood elevation, whichever is higher."
  • New York. Section R306.1.4 of the 2025 Residential Code of New York State, which the publisher lists as effective December 31, 2025, sets a "required flood elevation." At a minimum it is the higher of two figures. One is the base flood elevation plus "2 feet (610 mm) of freeboard" and "A sea level rise of 18 inches (457 mm) in flood hazard areas adjacent to tidal areas." The other is the elevation of the design flood on a flood hazard map adopted by the community or otherwise legally designated.

Ask the local floodplain administrator for the required elevation in writing.

Base flood elevation vs design flood elevation

The design flood elevation (DFE) is the term used in ASCE 24, the engineering standard for flood-resistant design, and in the Florida code above. FEMA's summary of the standard's 2014 edition says it uses the term "to acknowledge that some communities adopt flood hazard maps that depict flood hazard areas in addition to Special Flood Hazard Areas shown on FEMA's Flood Insurance Rate Maps (FIRM)." It continues: "The design flood elevation (DFE) equals the base flood elevation (BFE) in communities that regulate based on FIRMs. The DFE is always equal to or higher than the BFE."

Does base flood elevation affect flood insurance?

FEMA's pricing page says that since the 1970s rates were "predominantly based on relatively static measurements, emphasizing a property's elevation within a zone" on a flood map. Under the current approach, Risk Rating 2.0, FEMA says it incorporates "flood frequency, multiple flood types—river overflow, storm surge, coastal erosion and heavy rainfall—and distance to a water source along with property characteristics such as elevation and the cost to rebuild." The same page says "the NFIP's pricing approach does not use flood zones to determine flood risk."

So elevation still counts, as one property characteristic among several. We give no premium figures.

Can you change or challenge a base flood elevation?

FEMA describes three letters:

  • Letter of Map Amendment (LOMA). A letter stating that an existing structure or parcel "that is on naturally high ground and has not been elevated by fill" would not be inundated by the base flood. For a structure, FEMA's requirements page says "the lowest ground touching the structure" must be at or above the BFE. For lots, "The lowest point on the lot(s) must be at or above the BFE." As we read it, a LOMA leaves the BFE as published and finds the property at or above it.
  • Letter of Map Revision Based on Fill (LOMR-F). The same finding for a structure or parcel that "has been elevated by earthen fill." The requirements page lists two cases. For a structure, the lowest adjacent grade must be at or above the BFE, and the community must determine that the land and any existing or proposed structures to be removed from the flood hazard area are "reasonably safe from flooding." For lots, "Both the lowest point on the lot and the lowest floor of the structure must be at or above the one-percent-annual-chance flood elevation."
  • Letter of Map Revision (LOMR). FEMA's LOMR page calls it "a letter from FEMA officially revising the current NFIP map to show changes to floodplains, regulatory floodways, or flood elevations." As we read FEMA's pages, this is the letter that can change a published flood elevation.

Fees. FEMA's fee page, read November 16, 2026, says its schedule applies to requests postmarked on or after February 20, 2015. A single-lot or single-structure LOMA is free. A single-lot or single-structure LOMR-F is $525 on paper and $425 online, or $425 and $325 when it is based on as-built information and FEMA previously issued a conditional letter (CLOMR-F). A LOMR based on a bridge, culvert, channel, hydrology or a combination is $8,250 on paper and $8,000 online. Those are FEMA's review fees, not survey or engineering costs.

Base flood elevation when buying or developing land

Compare the ground to the BFE before you offer. A zone label says a site is in the floodplain. As we read it, comparing ground elevations with the BFE shows how much of the site is below the flood surface and by how much. That takes a topographic survey on the flood map's datum, or a conversion the surveyor documents.

Fill is regulated, and the floodway more so. 44 CFR 59.1 defines "development" to include "filling, grading, paving, excavation," and 60.3(b)(1) and (c)(1) have communities require permits for development in the mapped A zones. Where a community has adopted a regulatory floodway, 60.3(d)(3) requires it to:

"Prohibit encroachments, including fill, new construction, substantial improvements, and other development within the adopted regulatory floodway unless it has been demonstrated through hydrologic and hydraulic analyses performed in accordance with standard engineering practice that the proposed encroachment would not result in any increase in flood levels within the community during the occurrence of the base flood discharge."

Paragraph (d)(4) gives one other route. A community may permit floodway encroachments that would raise base flood elevations, provided it "first applies for a conditional FIRM and floodway revision," meets the requirements of 44 CFR 65.12 and "receives the approval of the Federal Insurance Administrator."

What the surveyor and the elevation certificate record. Our elevation certificate guide walks through the form: the BFE in item B9, its datum in B11, and the building's floor and adjacent grade elevations in section C, on the same datum as the BFE.

Before an offer, check:

  • The zone, the BFE and the datum across the whole boundary, not at one point.
  • The panel's effective date, any preliminary or pending map, and any LOMA, LOMR-F or LOMR on or near the site.
  • Whether any of the site is in a regulatory floodway.
  • The required building elevation, with freeboard, from the floodplain administrator.
  • In Zone A, whether the proposal is greater than 50 lots or 5 acres, and who will produce the BFE data.
  • If the site is outside the mapped floodplain, what Zone X does and does not settle.

Carry the answers into the land feasibility study, with the source and date beside each one.

Where Pillar fits

Pillar's map layers can show FEMA floodplain over parcel boundaries, which helps you see which sites touch a flood zone before you order a survey. A map layer is a screen, not a base flood elevation.

Quick answers

What does base flood elevation mean? It is the elevation floodwater is expected to reach in the base flood, the flood with a 1 percent chance of being equaled or exceeded in any year.

How do I find the base flood elevation for my address? Search the address at FEMA's Map Service Center, open the NFHL Viewer, and read the zone and elevation. Along rivers, use the Flood Insurance Study profile.

Is base flood elevation above sea level? It is a height above the vertical datum named for the flood map, such as NGVD 29 or NAVD 88.

What is the base flood elevation in Zone A? None is published. Federal rules have communities require proposals greater than 50 lots or 5 acres, whichever is the lesser, to include base flood elevation data, and reasonably use any data available.

How far above base flood elevation should I build? The federal minimum for new construction and substantial improvements of residential structures in Zones A1-30, AE and AH is the lowest floor, including basement, at or above the base flood level, unless FEMA has granted the community a basement exception. Florida's residential code, for flood hazard areas that are not subject to high-velocity wave action and not designated Coastal A Zones, requires the lowest floor at or above the base flood elevation plus 1 foot or the design flood elevation, whichever is higher. New York's residential code sets the required flood elevation at no less than the higher of two figures: the base flood elevation plus 2 feet of freeboard, and 18 inches more in flood hazard areas adjacent to tidal areas, or the design flood elevation on a flood hazard map adopted by the community or otherwise legally designated. Confirm your zone and the required elevation with the local floodplain administrator.