R4 Zoning: What It Means and What You Can Build
R4 zoning is an apartment district in some cities and a house-only district in others. Compare five real R4 codes, R3 vs R4 vs R5, and how to check a lot.
R4 zoning (also written R-4) is a residential zoning district whose meaning depends on the city or county. In some codes it is an apartment district. In others it allows only houses, at about four homes per acre. There is no national zoning code: the number sometimes counts steps up a density ladder and sometimes counts dwelling units per acre.
This guide is written by Pillar, a land research platform. The figures come from each jurisdiction's code or planning department, read on November 16, 2026. Codes change, so open the linked section before relying on a number. This is general information, not legal advice; confirm the rules for your lot with a licensed professional in your state.
What does R4 zoning mean?
The "R" means residential. The "4" means whatever the local code says it means. In the five codes we read, it means three different things:
- A step on a ladder. Los Angeles calls R4 a "Multiple Dwelling Zone" (LAMC section 12.11), one of its numbered zones from R1 to R5. New York City's districts run from R1 to R12, and the Department of City Planning says the numbers "refer to permitted bulk and density (with R1 having the lowest density and R12 the highest)" (Residence Districts guide).
- A density. Fairfax County, Virginia, names R-4 the "Residential District, Four Dwelling Units/Acre".
- A lot size or building type. Raleigh, North Carolina's R-4 is defined by a 10,000-square-foot minimum lot (UDO section 2.1.1). Baltimore, Maryland, names R-4 the "Detached and Semi-Detached Residential District" (Zoning Code section 8-210).
What can you build on R4 zoning?
Here are the five codes side by side, for the conventional case.
- Los Angeles, California (R4, Multiple Dwelling Zone). Section 12.11 allows any use permitted in the R3 Multiple Dwelling Zone, plus listed uses including child care facilities, dormitories, retirement hotels, eldercare facilities, churches "(except rescue mission or temporary revival)" and elementary and high schools or educational institutions. The section lists churches with the yards required in section 12.21 C, and schools with the yards required in section 12.21 C.3. Every lot needs a 50-foot width and 5,000 square feet, and the minimum lot area per dwelling unit is 400 square feet. A narrower or smaller lot can still be used if it "was held under separate ownership or was of record as of September 23, 1956," and was created in conformance with the Subdivision Map Act. That exception excludes uses explicitly requiring more than 5,000 square feet of lot area, and a lot under 4,000 square feet is limited to two dwelling units. Side yards are 5 feet for a main building of up to two stories (10% of the lot width, but no less than 3 feet, on a lot narrower than 50 feet), plus 1 foot for each story above the second, up to 16 feet. The rear yard is 15 feet, plus 1 foot for each story above the third, up to 20 feet. The front yard is the same as R3's; the Department of City Planning's zoning summary, updated January 2026, lists it as 15 feet, or 10 feet for key lots. Height depends on the lot's height district. The summary lists no height limit in feet for R4 in Height District 1, 75 feet in 1L, 45 feet in 1VL and 30 feet in 1XL. In Height District 1, section 12.21.1 caps total floor area at three times the buildable area of the lot.
- New York City (R4). The Residence Districts guide says R4 districts "allow a variety of housing types at a slightly higher density than R3-2 Districts," including attached townhouses, multi-family apartment buildings and detached or semi-detached residences. Section 23-11 of the Zoning Resolution, last amended December 5, 2024, requires 2,850 square feet and a 30-foot width for a single- or two-family detached residence in R4, and 1,700 square feet and 18 feet for other residences. The floor area ratio on a standard zoning lot is 1.00. For a detached house, the guide's table lists a 10-foot front yard, a 20-foot rear yard, two side yards of 5 feet each, a 35-foot building height, and lot coverage of 60% on an interior lot and 80% on a corner lot.
- Fairfax County, Virginia (R-4, four dwelling units per acre). Subsection 2102.7, whose ordinance note runs through May 6, 2026, says the district "provides for single-family detached dwellings and affordable dwelling unit developments." A conventional subdivision is capped at 4 dwelling units per acre, with an 8,400-square-foot minimum lot, an 8,800-square-foot average, and a width of 70 feet on interior lots and 95 feet on corner lots. For single-family dwellings on conventional lots, setbacks are 30 feet front, 10 side and 25 rear, and the height limit is 35 feet.
- Raleigh, North Carolina (R-4). Section 2.1.1 says R-4 allows single-unit living in a detached house or tiny house, and two-unit living in an attached house or tiny house, with a minimum lot size of 10,000 square feet. A detached house lot must be 65 feet wide and 100 feet deep, with setbacks of 20 feet from the primary street, 10 from a side lot line and 30 from the rear, and a height limit of 40 feet and 3 stories. Those are base numbers: the detached and attached house tables both answer yes for R-4 on the setback row "Residential infill rules may apply (see Sec. 2.2.7.)" and on the matching height row. Where section 2.2.7 applies, it sets the primary street setback from nearby buildings on the same block face and limits wall height next to the side property line. The table lists no maximum density for R-4, so as we read it the lot size is the control. Smaller lots and additional building types are permitted as part of a compact development.
- Baltimore, Maryland (R-4, detached and semi-detached). Section 8-201 says residential development in these districts "is limited to 1 single-family dwelling unit per lot." Table 8-401 sets a 3,000-square-foot minimum lot for a detached or semi-detached dwelling, a lot width of 30 feet for a semi-detached dwelling and 45 feet for all other uses, a 35-foot height limit, 45% lot coverage and 50% impervious surface. The rear yard is 25 feet. The front yard is 25 feet if less than 50% of the lots on the blockface are developed; otherwise it is the lesser of the blockface average or 40 feet.
Can you build a single-family home in R4?
A single-family house is a permitted use in all five codes, but Los Angeles also sets a minimum density. In Fairfax County, Raleigh and Baltimore the detached house is the main permitted housing type, and New York City's section 23-11 sets lot minimums for one in R4. Read the Los Angeles rule closely: R4 takes in R3's uses, the city's summary describes R3's as R2 uses plus apartment houses and multiple dwellings, and R2 takes in R1's (section 12.09). Under a paragraph added effective February 11, 2025, though, section 12.11 C.6 requires a minimum density of one dwelling unit or guest room, counting accessory dwelling units, for every 2,000 square feet of lot area for "every Housing Development Project on lots meeting the minimum width and lot area requirements for the zone, prior to any subdivision." The result is rounded up to the nearest unit. On a 7,500-square-foot lot that is 3.75, rounded up to 4. A single new house counts: the city's definition of Housing Development Project in section 12.03 includes "projects that involve no discretionary approvals and projects that include a proposal to construct a single dwelling unit." The rule has two outs. It does not apply when section 12.22 C.28 applies. That subdivision lists eight kinds of project or lot, among them a project whose only new dwelling units are accessory dwelling units and a lot that contains a Designated Historic Resource, and none of the eight applies on a site designated as a Lower Income Rezoning Housing Element Site. It also does not apply if the zone's minimum lot area per dwelling unit or guest room "does not allow for construction of the required minimum density." Ask the city whether one of these covers the lot before planning a single house alone.
Can you build a duplex in R4?
- Los Angeles: two units are a permitted use through the chain above, but a duplex alone can fall short of the minimum density. The 400 square feet per unit is a ratio, not a lot size: every R4 lot needs 5,000 square feet and a 50-foot width unless it qualifies under the older-lot exception above, and a lot under 4,000 square feet is limited to two dwelling units. On a 5,000-square-foot lot the minimum density works out to 2.5, rounded up to 3 dwelling units or guest rooms, counting accessory dwelling units. Two units with nothing else do not reach that unless one of the outs described above applies.
- New York City: yes. Section 22-122 applies to zoning lots that are not qualifying residential sites. It limits R4A lots to single- or two-family detached residences, and R4-1 and R4B lots to single- or two-family residences in the building forms it lists, which include zero lot line buildings. It states no such limit for plain R4.
- Raleigh: yes, as an attached house on a 10,000-square-foot lot, with the same base setbacks and height limit as a detached house, and the same infill note.
- Baltimore: no. Each lot gets one single-family dwelling unit, and section 8-201 prohibits converting a single-family dwelling to a multi-family dwelling.
- Fairfax County: not on a conventional lot, as we read it. Single-family attached units appear only in the affordable dwelling unit development standards, capped at 45% of the development's units.
Can you build apartments in R4?
- Los Angeles: yes.
- New York City: in plain R4, yes; the guide lists multi-family apartment buildings. In R4A, R4-1 and R4B, residences are limited to single- or two-family homes unless the lot is a "qualifying residential site," where section 22-122 permits any type of residence. The guide says sites close to transit, in commercial districts or with community facility uses can qualify, and lists a 5,000-square-foot minimum lot for them.
- Fairfax County, Raleigh and Baltimore: not under the conventional standards above. In Raleigh, section 2.1.1 says dimensional standards, density, building types and uses may be modified for R-4 within the TOD overlay or Frequent Transit Areas.
What is the difference between R3 and R4 zoning?
- Los Angeles: both are Multiple Dwelling zones with a 5,000-square-foot minimum lot. The city's summary lists 800 square feet of lot area per dwelling unit in R3. R4 halves that to 400 and adds the institutional uses above.
- New York City: the standard floor area ratio rises from 0.75 in the R3 districts to 1.00 in R4 (section 23-21). On qualifying residential sites it rises from 1.00 to 1.50.
- Fairfax County: both are single-family detached districts. Density rises from 3 to 4 dwelling units per acre, and the conventional minimum lot drops from 10,500 square feet in R-3 to 8,400.
- Baltimore: R-3 is a detached-only district with a 5,000-square-foot minimum lot. R-4 adds semi-detached dwellings and drops the minimum to 3,000.
Our guides to R1 zoning and R2 zoning cover the lower steps in several of the same codes.
What is the difference between R4 and R5 zoning?
- Los Angeles: section 12.12 halves the lot area per dwelling unit again, to 200 square feet, and adds private non-profit clubs or lodges chartered by the state, and hospitals or sanitariums other than animal hospitals, each "with yards as required in Sec. 12.21 C.3." The ordinary side and rear yards are the same as R4's.
- New York City: the standard floor area ratio rises from 1.00 to 1.50, and the guide lists a 45-foot building height in R5 against 35 feet in R4.
- Fairfax County: R-5 provides for "a mixture of single-family residential dwelling types" at 5 dwelling units per acre, with a 5,000-square-foot minimum lot for a detached house and standards for single-family attached dwellings.
- Baltimore: R-5 is in a different title of the code. Section 9-201 calls it the Transitional Residential District, meant to accommodate rowhouse developments and "limited low-rise multi-family garden apartment developments of a moderate density" as well as detached and semi-detached dwellings.
- Raleigh: there is no R-3 or R-5. Section 2.1.1 gives R-2 a 20,000-square-foot minimum lot and R-6 a 6,000-square-foot one. Townhouses do not start at R-6. Section 1.4.2 already allows them under R-4's conventional option, with a footnote: "In R-4, townhouse developments are restricted to a maximum of two dwelling units." For R-6, section 2.1.1 says "Multi-unit living is also allowed in a townhouse."
R4 zoning restrictions: which uses need special approval?
- Baltimore. Table 8-301 marks places of worship, primary and secondary schools, day-care centers, community centers, and bed and breakfasts "CB" in R-4. Section 1-205 says a "CB" indicates "a conditional use within that zoning district requiring approval by the Board of Municipal and Zoning Appeals."
- Los Angeles. Section 12.11 B requires prior approval under section 12.24.1 for any R4 use on a lot designated Public, Quasi-Public or Open Space on the community plan's land use map, and in three other listed cases.
Our guide to conditional use permits explains the process. Relief from a setback or height standard is a different request; see zoning variances.
How do you look up a parcel's zoning and read the R-4 rules?
Los Angeles. The Department of City Planning's ZIMAS brochure gives the steps:
- Go to zimas.lacity.org and search by address, street intersection, assessor parcel number or legal description.
- Expand the Planning and Zoning tab to see the underlying zone.
- Check whether the site is in a Specific Plan Area or Overlay Zone.
- Open section 12.11 for R4, then section 12.21.1 for the lot's height district and section 12.21 for parking and open space.
New York City.
- Open ZoLa, the city's Zoning and Land Use Map, and search by address or by borough, block and lot.
- Record the full district. R4, R4-1, R4A and R4B have different rules.
- Read that district's table in the Residence Districts guide, then confirm the numbers in the Zoning Resolution: section 22-122 for residence types, 23-11 for lot area and width, and 23-21 for floor area ratio.
- Check whether the lot is a qualifying residential site, defined in section 12-10.
What should a land buyer or developer check on an R4 lot?
Unit yield. Do the arithmetic from the code, not the label. Take a 7,500-square-foot lot, 50 feet wide, and compare base allowances only.
- In Los Angeles, 7,500 divided by 400 square feet per unit is 18.75, so 18 whole units at base density, and the minimum density rule sets a floor of 4. Whether 18 fit depends on the yards, parking, open space and the height district, which can mean no limit in feet or 30 feet on the same zone.
- In Baltimore, the same lot takes 1 single-family dwelling unit.
- In Fairfax County and Raleigh, it is under the conventional minimum lot (8,400 and 10,000 square feet), so ask how the code treats an existing undersized lot.
For raw land, work in acres. Fairfax County's cap of 4 units per acre allows at most 20 lots on 5 acres before streets, open space and unbuildable ground are taken out.
Parking and open space. In Los Angeles, section 12.21 A.4(a) requires "at least two automobile parking spaces on the same lot with each one-family dwelling thereon." For all other dwelling units it sets base ratios of one parking space for each dwelling unit of less than three habitable rooms, one and one-half for a unit of three habitable rooms, and two for a unit of more than three. The subdivision has exceptions. Section 12.21 G requires usable open space for new construction of six or more dwelling units on a lot: 100, 125 or 175 square feet per unit, depending on habitable rooms. In New York City, the Zoning Resolution sets parking by transit zone for dwelling units created after December 5, 2024. In the Inner Transit Zone, section 25-211 requires no accessory off-street parking spaces for them. For units created as part of a development or enlargement elsewhere, the base calculation is the number of dwelling units multiplied by a percentage. For a standard dwelling unit in R4 that is 35% in the Outer Transit Zone (section 25-222) and 50% beyond the Greater Transit Zone (section 25-232). Both tables have separate columns for other unit types, such as ancillary dwelling units at 0%, and both require no parking when the result is at or below a waiver number, which is 5 spaces for R4 in the Outer Transit Zone. Both tables also waive parking on qualifying residential sites in R1 through R5 districts with 75 or fewer dwelling units.
Coverage. Baltimore caps impervious surface at 50% in R-4, on top of the 45% lot coverage limit; see impervious surface limits for how such caps work.
Overlays and rezoning. An overlay or specific plan can change the base numbers. If R4 doesn't allow the project, the usual routes are a rezoning or a planned district. Start with the adopted plan; our guide to zoning vs. future land use explains how the two maps relate. A planned unit development is the site-specific alternative. If the lot adjoins a business district, read what commercial zoning allows.
Deal documents. The zoning label comes from the jurisdiction's zoning map and code, not from the listing. Confirm it with the planning office during due diligence. Then read the deed, the title commitment's exceptions, the recorded plat and any covenants, because private restrictions are separate from zoning and can be stricter.
Pillar's map layers show zoning alongside floodplain, wetlands, utilities and future land use over parcel boundaries. Coverage varies by dataset, and a map label is not the code, so confirm anything decisive with the jurisdiction.
Quick answers
What does R4 zoning mean? A residential district whose rules are set locally: an apartment zone in Los Angeles, a lower-density district open to several housing types in New York City, a four-homes-per-acre single-family district in Fairfax County, and a house district in Raleigh and Baltimore.
Can you build a duplex on R4? Yes in New York City and Raleigh, under each code's lot rules. Los Angeles permits two units, but its minimum density rule can require more than a duplex alone. Not in Baltimore's R-4, where each lot gets one single-family dwelling unit.
Can you build apartments on R4? In Los Angeles, and in New York City's plain R4 districts. Not under the conventional R-4 standards in Fairfax County, Raleigh or Baltimore.
What is the minimum lot size in R4? There is no standard. For a detached house under the conventional standards above, it runs from 2,850 square feet in New York City to 10,000 in Raleigh.
Is R4 high density? In Los Angeles, yes: 400 square feet of lot area per unit works out to about 109 units per acre by our arithmetic. In Fairfax County it means 4.