Townhome Development: Zoning, Platting and Ownership
How townhome development works: fee-simple lots vs. condos, zoning in Raleigh, Fairfax County and Spokane, a yield check and site screening.
Townhome development builds side-by-side single-family attached homes separated by ground-to-roof walls, for sale or rent. For-sale projects can use platted fee-simple lots or condominium units with shared common elements; that choice sets subdivision/financing paths and can affect zoning where codes require individual lots.
By Pillar, a land research software company. Linked sources were read November 21, 2026; verify before relying on figures. General information only; confirm local rules with a licensed attorney, surveyor or planner.
What is townhome development?
"Townhome" and "townhouse" name a building form, not one legal category:
- Building code. The 2021 International Residential Code (where adopted, often amended) defines a townhouse as a building with 3+ attached townhouse units extending foundation to roof, each with a yard or public way on at least two sides (2021 IRC Chapter 2).
- Federal data. Under Census Survey of Construction definitions, attached units count as single-family only when each has a ground-to-roof wall, separate heating, individual public-utility meters and no units above or below; otherwise Census classifies them as multifamily.
- Tenure. Built for sale or rent; for single-owner rentals, see build-to-rent.
Census's November 18, 2026 Table Q1 (rounded thousands) reports about 40,000 privately owned single-family attached starts in preliminary Q3 2026 data vs. 46,000 in Q3 2025; those rounded privately owned quarterly counts sum to 154,000 over four quarters through Q3 2026 vs. 179,000 a year earlier. A November 20, 2026 NAHB analysis puts Q3 townhouses at 17% of single-family starts, with the one-year moving average falling to 17% from a record 18.7% in Q3 2025.
Fee-simple vs. condo approvals
Fee-simple townhomes (subdivision plat)
Each home sits on a deeded zero lot line lot along shared walls; an HOA can hold shared drives, stormwater tracts or open space. Creating individual lots generally requires subdivision platting (plat map guide).
North Carolina G.S. 160D-802 covers divisions into 2+ lots or building sites for immediate or future sale or building development, plus divisions involving new-street dedications or changes to existing streets, subject to subsection (a) exemptions (e.g., a single-ownership tract <=2 acres split into <=3 locally compliant lots with no street right-of-way dedication). In Raleigh and its ETJ, UDO Sec. 10.2.5 requires preliminary plans, infrastructure construction plans and a recorded final plat unless exempt (Sec. 10.2.5.B) or a Minor Subdivision under Sec. 10.2.5.H.3 (all five criteria: abuts only existing Local Streets per Sec. 8.5.2.B, lies entirely within one or more of R-1, R-2, R-4, R-6 and R-10, <=6 lots, no new public street, and no part of the parent tract was in a recorded Minor Subdivision during the preceding five years). Minor Subdivisions skip preliminary plans (Sec. 10.2.5.E.1) but need Site Plan Review (Sec. 10.2.8) before final plat approval and recording (Sec. 10.2.5.F.6, 10.2.5.H).
Texas Local Gov't Code § 212.004 requires a prepared, recorded plat to divide a tract in a city or ETJ into 2+ parts for lots or public dedications. Its five-acre exclusion (§ 212.004(a)) applies only when every resulting part exceeds five acres, each has access and no public improvement is dedicated; check municipal classifications under § 212.0045.
Townhome-style condominiums
Census notes condominium ownership may apply to single-family and multifamily structures. N.C.G.S. 47C-1-103(7) defines a condominium as real estate with portions for separate ownership and the rest for common ownership solely by those owners, with vested undivided common-element interests. State acts govern plat/plan filing (separately recorded under N.C.G.S. 47C-2-109; with or separate from the declaration under Tex. Prop. Code § 82.059).
N.C.G.S. 47C-1-106 and Tex. Prop. Code § 82.006 bar zoning, subdivision or building codes from banning condos or adding rules not applied to substantially similar (NC) or physically identical (TX) non-condo projects, leaving general codes intact. Recording rules differ:
- North Carolina. Under N.C.G.S. 47C-2-101(b), a declaration or unit-adding amendment cannot be recorded until all structural components and mechanical systems of buildings containing those units are substantially completed to the licensed architect's or registered engineer's design plans, evidenced by their recorded certificate of completion. Units or portions bounded solely by surface, airspace, subterranean space or a specified combination are excepted (G.S. 47C-2-105(a)(5)).
- Texas. Under Tex. Prop. Code § 82.051(d), county clerks record declarations, amendments and condo plats or plans without prior approval from any other authority. Under subsection (f), a condo plat or replat (including amendments to either) needs an original certificate from each taxing unit with jurisdiction showing no delinquent ad valorem taxes. If a certificate omits the preceding year, attach that taxing unit's collector-issued receipt showing those taxes were paid. Taxing-unit acquisitions for public use (eminent domain or voluntary sale) are exempt. Subsection (e) preserves municipal and county plat and building-code authority.
Buyer financing rules
Under Fannie Mae's Selling Guide (August 5, 2026), B4-2.1-02 waives review for new and established PUDs, except manufactured-home PUDs on a community land trust, ground lease or shared equity arrangement. Under B4-2.3-01, a PUD requires automatic, nonseverable HOA membership, mandatory assessments, HOA-owned and maintained common property/improvements, and no condo or co-op status; zoning alone does not make a PUD.
For condo purchase loans (excluding manufactured homes or projects with any manufactured home), B4-2.1-02 waives review in three categories: detached condo units (including those in mixed attached/detached projects), 2-to-4-unit projects, and 5-to-10-unit projects outside a larger development or master association. Attached units in a 5-to-10-unit condo inside one need Full Review, and larger attached condos fall outside purchase waivers. A separate waiver covers eligible limited cash-out refinances of Fannie Mae-owned condo loans up to 80% LTV. Projects with >10 attached units, or 5-to-10 attached units in a larger development or master association, must have no unaddressed critical repairs or evacuation orders. Other eligibility and insurance rules still apply.
Townhome zoning in three municipal codes
District labels vary; see R3 zoning and R4 zoning.
Raleigh, North Carolina (UDO, Supplement 28)
- Permitted zones. Sec. 1.4.1.C defines a Townhouse as 2+ horizontally integrated units separated by a party wall, on individual lots or one lot. Sec. 1.4.2 allows Townhouse and Sec. 6.1.4 permits Multi-unit Living by right (Sec. 6.1.3) in R-6 and R-10. Mixed-use zones RX-, OX-, NX-, CX- and DX- allow Townhouse (not OP-/IX-; barred under Shopfront
-SHin all five and Green Plus-GPin RX-); check Sec. 1.4.2 frontages and Sec. 6.1.4 uses (Sec. 3.2.3). - R-1, R-2 and R-4 limits. R-1 bars townhouses outside
-TOD(Sec. 5.5.1 permits Townhouse in all residential districts under-TOD). In R-2/R-4, Sec. 1.4.2 fn. (1)–(2) and Sec. 2.2.3 fn. ii cap conventional townhouses at two units, allowing 3+ in-TOD. For limited-use 3+ paths, Sec. 6.2.1 points to conservation (Sec. 2.4.1, Sec. 2.4.4: townhouse unit type max 50% in R-2; open space the greater of 40% or 4 ac in R-2, or 40% or 2 ac in R-4), R-4 compact (Sec. 2.3.1: open space the greater of 20% or 1 ac; lists Townhousen/ain R-2 and Sec. 2.3.4 omits R-2 despite Sec. 1.4.2), or R-4 frequent transit (Sec. 2.7.1.G: each lot partly in mapped area; cannot combine with compact or conservation; 12-unit cap unless affordable units equal >=20% of units over 12 for households at <=60% AMI for >=30 years from CO; fn. 7: city rent and income limits apply, record the city-approved deed restriction before CO, report compliance annually and build affordable units concurrently). Conventional two-unit townhouses follow Sec. 2.2.2 as modified by Sec. 2.2.3 fn. i. - Conventional R-6/R-10 rules. Sec. 2.2.3 sets min net site area/unit (Sec. 1.5.1.B excludes existing/proposed public streets or right-of-way) at 4,500 sq ft (R-6) and 3,000 (R-10), site width 50 ft / 45 ft, 10% outdoor amenity, no min lot area, 16-ft lot width, 10-ft separation, 45 ft / 3 stories max height and site setbacks: 10 ft primary/side street, 10 ft (R-6) / 6 ft (R-10) side site line, 20 ft rear (a permanently recorded open or common-area lot at least 20 ft wide may satisfy the rear setback, fn. iii); check Sec. 2.2.7 infill rules.
Fairfax County, Virginia
- Permitted zones. Sec. 9103 defines Dwelling, Single-Family Attached as single-family units in one structure separated by fire-rated foundation-to-roof party walls, each with its own entry to an outdoor sidewalk or walkway without passing through a lobby or shared-use area, on one parcel or adjoining lots. Table 4101.1 permits (
P) it in R-5, R-8, R-12, R-16 and R-20, and in R-2–R-4 only as an Affordable Dwelling Unit (ADU) development (not R-1). - Base standards. Non-ADU R-8 (Table 2102.13) allows 8 du/ac (9.6 ADU, Table 2102.14), 5-ac district min, 20% gross open space (5100.3.A(3)), no min lot area, 18-ft lot width, 200 sq ft privacy yard/lot and 35-ft height. Non-ADU R-12 (Table 2102.15) allows 12 du/ac (14.4 ADU, Table 2102.16), 4-ac min, 25% open space and no privacy yard.
- Rows, setbacks and waivers. 4102.3.B caps contiguous building groups at 250 ft, excluding any utility closet. Table notes cite 5100.2.D(1)(d) and 5108.5 (transitional screening) for setbacks. Under 5100.2.K, the Board may waive district size or lot width in R districts (excluding non-R-1 cluster subdivisions) with a rezoning or special exception, only on 5100.2.K(2) or (3) findings.
Spokane, Washington
- Permitted zones. SMC 17A.020.010 defines Attached Housing as 2+ single-unit residences on individual lots attached by a common wall at a shared property line ("townhouses, townhomes, or row houses"), inside Middle Housing. Table 17C.111.115-1 (eff. Jan. 18, 2026) permits Middle Housing in R1, R2, RMF and RHD, not RA.
- Density and lots. Under Table 17C.111.205-1 and SMC 17C.111.210(J)(1), no max density applies on sites <=2 acres (excluding critical areas; proposed new right-of-way may be subtracted), subject to Airfield Overlay limits (SMC 17C.180.090). Above two acres after the applicable deductions, base caps are 10 units per adjusted acre in R1 and 20 in R2. RMF and RHD have no base cap. Notwithstanding the density max, up to six middle-housing units including ADUs are allowed per lot, still subject to other site development standards (17C.111.210(J)(2)), and R1/R2 land divisions count one lot as one unit (17C.111.210(I)). Min densities apply unless exempted (17C.111.210(K)): 4 (R1), 10 (R2), 15 (RMF/RHD). Conventional R1–RHD lots require 1,200 sq ft and 15-ft width/frontage (RA: 7,200 sq ft, 40 ft; R1–RHD widths increase in Airfield Overlays); min depth is 80 ft (R1) and 40 ft (R2).
- Unit Lot Subdivisions and coverage. Under SMC 17G.080.065 (eff. March 6, 2025), Unit Lot Subdivisions of 2+ units on parent sites <=2 acres in residentially allowed zones allow "child" lots down to footprint (building/fire codes apply) while setbacks, building coverage, design standards, street frontage and density apply to the parent site. Aggregate coverage (primary + accessory, overall site per Table 17C.111.205-1 note [6], pre-17C.111.225 bonus) is 65% R1, 80% R2 and 100% RMF/RHD. Table 17C.111.205-2 separately caps footprint per primary building in R1/R2 (2,450 sq ft <=7,000 sq ft lot; 35% >7,000 sq ft); 17G.080.065 does not state whether parent site or child lot area applies, so confirm with Spokane planning. <=9 lots run as short plats (10+ as subdivisions); driveways cannot serve >9 units without City Engineer approval. See Table 17C.111.205-2 for height, setbacks and outdoor space, and -3 for bonus coverage.
Townhomes per acre: hypothetical 2.0-acre site
Hypothetical site, not a real parcel; counts are our base-rule arithmetic, not city determinations. Two acres = 87,120 sq ft (how big is an acre).
- Raleigh R-6/R-10 (conventional): If all 87,120 sq ft are net site area (Sec. 1.5.1.B), R-6 yields 19 units (19.36) and R-10 29 (29.04; fractions add no unit here), needing 8,712 sq ft outdoor amenity, 50-ft/45-ft site width and 16-ft lot widths.
- Fairfax R-8 (base, non-ADU): At 8 du/ac, 2.0 acres yields 16 units, 17,424 sq ft open space, 18-ft lot widths and 200 sq ft privacy yards/lot. In a straight 18-ft/unit row, 13 units = 234 ft and 14 = 252 ft (before layout or utility-closet exclusions). A standalone 2.0-acre rezoning needs a discretionary 5100.2.K Board waiver on its listed findings.
- Spokane R1 (2.0-acre parent site, outside Airfield Overlays): With no deductions or min-density exemption, no max applies and base min is 8 lots (4 du/ac). Physical rules govern: 65% aggregate coverage (56,628 sq ft pre-bonus), the Table 17C.111.205-2 per-primary-building footprint cap (confirm lot-area basis with Spokane), setbacks, outdoor space and the 9-unit driveway cap absent City Engineer approval.
Real sites lose units to drives, alleys, parking, fire turnarounds, stormwater, buffers, open space, setbacks, infill, separation, easements, floodplains, wetlands and slopes.
Townhome site screening checklist
- Zoning. Confirm district, overlays and whether 3+ units are by right, capped at two (Raleigh R-2/R-4) or need rezoning or planned unit development.
- Density and dimensions. Verify gross vs. net area, site/lot widths, row length, height and open space.
- Ownership path. Confirm fee-simple, unit lot subdivision or condo paths, recording triggers and buyer loan limits.
- Access. Verify road frontage vs. legal access, driveway caps, alleys and fire turnarounds with the civil engineer and fire marshal.
- Utilities. Ask local utilities whether fee-simple lots need separate laterals, taps and meters; request capacity, terms, tap fees and a will-serve letter.
- Stormwater. Size stormwater for impervious cover with a civil engineer (detention vs. retention pond, impervious surface limits); check FEMA's Flood Map Service Center and USFWS Wetlands Mapper (NWI FAQ).
- Covenants. Check recorded deed restrictions for detached-only clauses, lot minimums or leasing bans.
Horizontal costs (taps, drives, stormwater, impact fees) vary; budget from bids and fee schedules, not per-unit averages (land feasibility study).
Finding land and deal documents
Target attached-housing infill, higher-density residential, qualifying mixed-use or edge-of-growth tracts near utilities where future land use supports medium density (off-market land).
Check the deed and title commitment for covenants, shared drives and easements. Use a survey to check widths; to plot setbacks on an ALTA/NSPS survey, request Table A item 6(b) and provide a site-specific zoning report or letter with setbacks the surveyor can plot without interpretation. Pull plats, HOA and master-association docs (for Fannie Mae's 5-to-10-unit condo waiver).
Pillar shows available zoning facts, acreage and mapped FEMA flood zones over parcel boundaries (Pillar for homebuilders); confirm official ordinances, plats and utility capacity locally.
Quick answers
How many townhomes can you build per acre? Code controls: base Fairfax R-8 caps density at 8 du/ac (R-12 at 12); conventional Raleigh requires 4,500 sq ft net site area/unit in R-6, 3,000 in R-10 (9 and 14 whole units/net acre by site-area arithmetic, before other site constraints); Spokane sets no max on R1/R2 sites <=2 acres (after excluding critical areas and subtracting proposed new right-of-way if elected) or in RMF/RHD, subject to Airfield Overlays.
Can you build townhomes on a single-family zoned lot? Check the attached-housing rules applying to the lot. Spokane permits Middle Housing in R1/R2 (subject to Airfield Overlay limits, SMC 17C.180.090). Raleigh bars townhouses in R-1 outside -TOD and caps conventional R-2/R-4 at two units unless -TOD or a qualifying alternate option applies (conservation in R-2/R-4; compact or frequent transit in R-4, each under the cited requirements). Fairfax R-1–R-4 bar standard attached dwellings outside R-2–R-4 ADU developments.